
This product is a waterproof LED lamp most suitable for internal lighting of machine tools. The mounting hole positions are the same as those of the previous NLM series.
The appearance is a glass tube with high light transmittance and a fiberglass nylon end cap, which makes the whole tube strong and durable.
The power supply uses a constant current IC drive circuit method, which can maintain the brightness of the lamp unchanged even if the voltage changes, and can increase the life of the LED.
The independently developed protection circuit design has a certain degree of protection against inrush currents, surges, or instantaneous power outages.
The unique optical design eliminates the glare and multi-layer overlapping phenomena unique to LEDs and achieves high-intensity natural light.
Lighting inside machine tools, industrial machinery lighting, equipment machinery lighting, etc.

NLM SN2 series lamps are designed with a diffusion plate on the LED light source; it can improve the messy reflected light source of LED and present a uniform light source.

| color temperature | 5,700K |
|---|---|
| life expectancy | Operating temperature 40℃ 40,000 hours ※Life span is based on initial illumination reduced to 70% |
| Use temperature | -10℃~40℃ |
| Appearance material | glass tube |
| protection level | IP67 |
| Standard wiring | DC 3m(VCTF0.5mm²x2C) AC 3m(VCTF0.75mm²x2C) |
| Certification |
|
| Select accessories | oil resistant wire |
|---|---|
| Wire protective cover (single side corrugated pipe connector) Wire protective cover (double-sided corrugated pipe connector) |
|
| Fixed magnet (ND-P04) Fixed iron clip (NC-562B) |
|
| 2m cord with plug (AC110V) |
The safe flicker rate recommended in IEEE 1789 (Standard for Effects and Evaluation of Lighting Flicker) is 8%, while flicker is almost undetectable to the human eye at about 3%.
Nikki product adopt an exclusive design to further reduce the flicker rate to less than 2%. Not only will there be no flicker at all when shooting general still photos and videos, but it can also use 240fps There will be no stripe flicker when shooting with high frame rate equipment. It is very suitable for application scenarios such as image inspection and appearance inspection that require high-precision photography or long-term naked eye observation.
※The picture below shows the situation under the light source of a Nikki product.
[General LED] Flickers and streaks may be observed during photography
[Nikki product] Mild and even light, no flicker
| model | drawing | Luminous flux | Illuminance (1m) | power supply | Power consumption |
|---|---|---|---|---|---|
| NLM10SG-AC-SN2 | PDF DXF 3D STEP | 710 lm | 720 lx | AC100 - 240V | 5.5W |
| NLM10SG-DC-SN2 | PDF DXF 3D STEP | DC24V | |||
| NLM20SG-AC-SN2 | PDF DXF 3D STEP | 1,050 lm | 1,050 lx | AC100 - 240V | 7.5W |
| NLM20SG-DC-SN2 | PDF DXF 3D STEP | DC24V | |||
| NLM30SG-AC-SN2 | PDF DXF 3D STEP | 1,900 lm | 1,800 lx | AC100 - 240V | 15W |
| NLM30SG-DC-SN2 | PDF DXF 3D STEP | DC24V | |||
| NLM40SG-AC-SN2 | PDF DXF 3D STEP | 2,710 lm | 2,680 lx | AC100 - 240V | 22.5W |
| NLM40SG-DC-SN2 | PDF DXF 3D STEP | DC24V | |||
| NLM50SG-AC-SN2 | PDF DXF 3D STEP | 3,370 lm | 3,150 lx | AC100 - 240V | 30W |
| NLM50SG-DC-SN2 | PDF DXF 3D STEP | DC24V |

※Plastic fixed end cap included
| model | A | B |
|---|---|---|
| NLM10SG-DC/AC-SN2 | 310 | 300 |
| NLM20SG-DC/AC-SN2 | 500 | 490 |
| NLM30SG-DC/AC-SN2 | 690 | 680 |
| NLM40SG-DC/AC-SN2 | 930 | 920 |
| NLM50SG-DC/AC-SN2 | 1350 | 1340 |
Wire protective cover
Fixed iron clip
fixed magnet

| model | size | Material | power supply | series | Optional |
|---|---|---|---|---|---|
| NLM |
|
|
※Please use single-phase AC power supply. |
|
|